![]() For pages that want to do inline require() calls, it is best to nest those inside a require() call for the configuration: ![]() ![]() data-main is only intended for use when the page just has one main entry point, the data-main script. If you want to do require() calls in the HTML page, then it is best to not use data-main. load 'scripts/foo.js' instead of 'scripts/libs/foo-1.1.3.js' When that happens, require.js will attempt to This code might be called before the nfig() in main.js This means that you cannot assume that the load and execution of your data-main script will finish prior to other scripts referenced later in the same page.įor example, this arrangement will fail randomly when the nfig path for the 'foo' module has not been set prior to it being require()'d later: Note: the script tag require.js generates for your data-main module includes the async attribute. You will typically use a data-main script to set configuration options and then load the first application module. The data-main attribute is a special attribute that require.js will check to start script loading: If you do not express the dependencies, you will likely get loading errors since RequireJS loads scripts asynchronously and out of order for speed. However, you may need to use some traditional/legacy "browser globals" scripts that do not express their dependencies via define(). Ideally the scripts you load will be modules that are defined by calling define(). For instance, configure "jquery" to be "jquery-1.7.2". This allows you to have the very minimal configuration instead of having to put an entry in the "paths" config for each library. It is recommended to store that version info in a separate text file if you want to track it, or if you use a tool like volo, it will stamp the package.json with the version information but keep the file on disk as "jquery.js". Notice as part of that example, vendor libraries like jQuery did not have their version numbers in their file names. ![]() jQuery, canvas and the app/sub module are all the paths config could be for a directory. except, if the module ID starts with "app", By default load any module IDs from js/lib Similarly, to avoid a bunch of configuration, it is best to avoid deep folder hierarchies for scripts, and instead either keep all the scripts in baseUrl, or if you want to separate your library/vendor-supplied code from your app code, use a directory layout like this: By doing so, it gives you more flexibility in renaming and configuring the paths to different locations for optimization builds. In general though, it is best to use the baseUrl and "paths" config to set paths for module IDs. Contains an URL protocol, like "http:" or "https:".If a module ID has one of the following characteristics, the ID will not be passed through the "baseUrl + paths" configuration, and just be treated like a regular URL that is relative to the document: There may be times when you do want to reference a script directly and not conform to the "baseUrl + paths" rules for finding it. All of these capabilities allow you to use smaller strings for scripts as compared to traditional tags. RequireJS will automatically add it when translating the module ID to a path. RequireJS also assumes by default that all dependencies are scripts, so it does not expect to see a trailing ".js" suffix on module IDs. If there is no explicit config and data-main is not used, then the default baseUrl is the directory that contains the HTML page running RequireJS. Or, baseUrl can be set manually via the RequireJS config. This example will end up with a baseUrl of scripts: The data-main attribute is a special attribute that require.js will check to start script loading. The baseUrl is normally set to the same directory as the script used in a data-main attribute for the top level script to load for a page. RequireJS loads all code relative to a baseUrl. As part of that, it encourages using module IDs instead of URLs for script tags. While it can also run fast and optimize well, the primary goal is to encourage modular code. RequireJS takes a different approach to script loading than traditional tags. How could I import jQuery without conflict with dojo? I would very much appreciate your assistance.ĭefine. I searched for a solution and tried it a few (code below), but they didn't work at all. I would like to use ArcGIS JavaScript API 4.3 with jQuery, but I am getting following errors.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |