The fact is, when an error occur, Windows don't want to deal with the device any more, even through another USB port, like a kind of blacklist system. Here it was recognise by windows immediately as an unknown device (because flash was corrupted), so I was able to use the boot loader method, reflash the firmware, and after this it worked fine on my desktop too! After this nothing was working, really nothing, no Windows detection, no led, nothing, until I decide to use the laptop instead of my desktop. It worked once at the beginning, I started to update the firmware, and it get stuck during the process. Ok, here some hope: I had the exact same issue with the T500RS, not with the TH8 RS. Very sad for you, I read how you was happy to get this. I was so itching to get to drive manual cars again with a proper H shifter but faith as it seems has other plans. One post from some forum by someone, said that they lose the device as soon as they try to update the firmware and the way they get it back is to return to the old firmware by using the "bootloader method" which in my case doesnt help.Ībsolutely awesome piece of gear, if only it would work. Also I believe they have newer version of the main PCB v2 I believe they call it, so hopefully I get that one incase this didnt have it already.Īnybody else had this same type of issue? DOA or otherwise lose the device from control panel so that it cant be regocniced anymore by windows? I send them a reply that I'd rather take the new PCB, saves me the hassle to send this one back and also place I bought this one from doesnt have these anymore th8rs on the self so I would be in a long wait to get a replacement. 2) they can send me a new main PCB (printed circuit board) and directions how to change it. I send an email to Thrustmaster and they said that my assessment is correct and I have two options.ġ) send it back and get a new one from the vendor. Symptoms were quite clear, couldnt install the plug'n'play drivers, couldnt update firmware, device didnt show in control panel nor its own software with manually installed drivers. If the problem persists, please contact Thrustmaster’s technical support team, who will guide you through the necessary steps to be taken.Got my shifter in the mail yesterday, spended about 3 hours wrestling with it and came to the conclusion that its internal memory is dead and so it cant send nor receive data from. Please note: if the shifter is not detected in the Firmware Updater window or if the update fails, try carrying out the same procedure using different USB ports on your PC, to see if that resolves the problem. Once the message indicating that the firmware update has been successful appears, you can close the window by clicking the X in the top right-hand corner. TH8A Shifter – Ver: / TH8 RS Shifter – Ver: appears under Device. Launch the Thrustmaster firmware updater ( Start / All Programs / Thrustmaster / TH8A / Firmware Updater).ħ. Please note that at this stage, Windows will not detect the shifter in the Game Controllers panel: this is completely normal.Ħ. As soon as the USB cable is connected, you can release the button. While still holding the button pressed down with the screwdriver, plug the USB cable directly into one of the USB ports on your PC: do not use any USB extenders or USB hubs.ĥ. Press (and keep pressing down on) this button using a small screwdriver - you must hear a little “click” noise:Ĥ. On the underside of the TH8 shifter, just next to the USB cable, there is a small hole providing access to a small rectangular black button:ģ. Install the latest drivers available from Thrustmaster’s technical support website for your shifter model:Ģ. If your TH8 shifter (TH8A/TH8 RS) is no longer detected and/or recognized by the PC/console, follow the instructions below in order to connect the shifter to a Windows-based PC in bootloader mode:ġ. My TH8 shifter is no longer recognized by my PC/console.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |